What is R7 zoning in NYC?

R7 districts are medium-density apartment house districts mapped in much of the Bronx as well as the Upper West Side in Manhattan and Brighton Beach in Brooklyn.

What are the 3 zoning districts in NYC?

New York City is divided into three basic zoning districts: Residence (R), Commercial (C) and Manufacturing (M). The three basic districts are further sub-divided to allow for a wide range of building forms and uses.

What is R6 zoning in NYC?

R6 zoning districts are widely mapped in built-up, medium-density areas in Brooklyn, Queens and the Bronx. The character of R6 districts can range from neighborhoods with a diverse mix of building types and heights to large-scale “tower in the park” developments such as Ravenswood in Queens and Homecrest in Brooklyn.

What is R5 zoning in NYC?

R5 districts allow a variety of housing at a higher density than permitted in R3-2 and R4 districts. The floor area ratio (FAR) of 1.25 typically produces three-and four-story attached houses and small apartment houses.

What is R9 zoning in NYC?

R9 Zoning is considered “high density” residential zoning. R9 is a Residential Zoning Districts with higher floor area ratios and results in larger buildings. It typically has large multifamily buildings including high rise residential towers.

The Plan To Literally Expand New York City - Cheddar Explains

What is Group R occupancy in NYC?

In buildings in Occupancy Groups R- 1 and R-2 that are two stories in height and in Occupancy Group R-2 that are three stories in height with not more than one dwelling unit per story, access to the roof shall be permitted to be a noncombustible roof hatch or trap door not less than 21 inches (533.4 mm) in width and 28 ...

What is R1 zoning in NYC?

R1 districts are leafy, low-density neighborhoods of large, single-family detached homes on spacious lots. Resembling many suburbs, these districts are mapped in a few areas of the city, such as Todt Hill (R1-1) in Staten Island, Jamaica Estates (R1-2) in Queens, and Fieldston (R1-2) in the Bronx.

What does R4 and R5 mean?

R4 or I4. You paid your credit back in 4 months. You were late 90 days. R5 or I5. You have not repaid in four months.

What is R3 zoning in NYC?

R3-1 contextual districts are the lowest density districts that allow semi-detached one- and two-family residences, as well as detached homes. R3-1 districts generally follow existing patterns of development in the Bronx, Queens, Staten Island and south Brooklyn.

What is R4 zoning in NYC?

Primarily a contextual rowhouse district limited to low-rise, one- and two-family attachedresidences, R4B districts also permit detached and semi-detached buildings. However, the floor area ratio (FAR) of 0.9 and maximum building height of 24 feet typically produce a two-story, flat-roofed rowhouse.

What is R Zone land?

R-zone means residential zone that states undertaking construction for residential purposes only.

What is R2 zoning in NYC?

Residential development in R2 districts is limited exclusively to single-family detached houses. Floral Park in Queens, parts of City Island and Riverdale in the Bronx, and Westerleigh on Staten Island's north shore are typical R2 districts.

How high can you build in NYC?

New York City does not generally limit building heights, but instead controls bulk and density by what's called the floor area ratio (FAR). This means that a residential developer can build nine times the square feet of the lot area in an R-9 district.

What are 4 land use zones?

What is an R 3 building NYC?

R3-1 Zoning is a low density residential zoning contextual district in NYC. You can build single family or 2 family homes that are either detached or semi detached in R3-1. The R3-1 Zoning District is a contextual sub district of R3 Zoning in NYC.

What are the 5 districts in New York City?

If you're not sure what the 5 boroughs of New York City are, they're the five districts that make up NYC: Manhattan, Brooklyn, Queens, the Bronx, and Staten Island.

What is R-3 occupancy NYC?

310.1.3 Group R-3

This group shall include, but not be limited to, the following: Convents and monasteries with fewer than 20 occupants in the building Page 19 Group homes One- and two-family dwellings, including the following: 1.

What is R zone in real estate?

RESIDENTIAL ZONE R-2

R2 zone is residential zone with road below with 12 m & above, access road (9 m in congested area) almost all uses are permissible in R2 zone eg. Residential, commercial, hospital, institute etc. Following are uses permissible in residential zones.

What does R-3 stand for in real estate?

MULTIPLE-FAMILY RESIDENTIAL ZONE (R3)

What is R1 R2 R3 R4 R5?

Circles (R1, R2, R3, R4, R5) indicate the five base estations used for collection. In each of these named regions there are three collection points, represented by the points in each region. Source publication. Exploiting the Use of Convolutional Neural Networks for Localization in Indoor Environments. Article.

What does R1 R2 R3 R4 mean?

Terminals R1/R2 and R3/R4 indicate the normally closed power poles of this 4-pole contactor while terminals 1/2 and 3/4 indicate the normally open power poles.

What does R1 R2 R3 R4 R5 represents in architecture?

R1 – General Residential. R2 – Low Density Residential. R3 – Medium Density Residential. R4 – High Density Residential.

What is difference R1 and R2?

The main difference between the R1 and R2 is the weight of the fleece. As the names suggest, the R1 line features lighter-weight fleece while the R2 is heavier.

What is the difference between R1 and R2?

R1 doctoral universities are considered to have the “highest research activity.” R2 universities are considered to have “higher research activity.” Finally, R3 schools have “moderate research.”

What is R1 vs R2?

R1: Doctoral Universities – Very high research activity. R2: Doctoral Universities – High research activity. D/PU: Doctoral/Professional Universities.